Ar kompiuterių ventiliatoriai visada veikia 100%, jei nenurodyta kitaip?

Turinys:

Ar kompiuterių ventiliatoriai visada veikia 100%, jei nenurodyta kitaip?
Ar kompiuterių ventiliatoriai visada veikia 100%, jei nenurodyta kitaip?

Video: Ar kompiuterių ventiliatoriai visada veikia 100%, jei nenurodyta kitaip?

Video: Ar kompiuterių ventiliatoriai visada veikia 100%, jei nenurodyta kitaip?
Video: How to Stop Android Apps from Spying on You - YouTube 2024, Gegužė
Anonim
Nesvarbu, ar nešiojamieji kompiuteriai, staliniai kompiuteriai ar net žaidimų konsolės, mes visi girdėjome sistemos ventiliatorių bangą fone. Kaip tiksliai visi šitieji aušinimo ventiliatoriai žino, kada atsukti, nuleisti ir kitaip sumažinti oro kiekį, kurį juda?
Nesvarbu, ar nešiojamieji kompiuteriai, staliniai kompiuteriai ar net žaidimų konsolės, mes visi girdėjome sistemos ventiliatorių bangą fone. Kaip tiksliai visi šitieji aušinimo ventiliatoriai žino, kada atsukti, nuleisti ir kitaip sumažinti oro kiekį, kurį juda?

Šiandien "Klausimų ir atsakymų sesija" pateikiama su "SuperUser", "Stack Exchange", "Community-driven Q &A" tinklalapių grupe.

Klausimas

SuperUser skaitytuvas darkAsPitch stebisi:

What happens if I do not plug it into the motherboard and it does not have a switch?

I have seen fans before with an “off/low/high” switch that allows you to manually set their speed.

I have seen fans that plug into the motherboard and are controlled by the OS.

I am curious… what does a fan do by default when plugged into a PSU? Does it run at 100% unless otherwise told to go slower? This is what I would expect…

Taigi, kaip jie veikia? Visiškas, jei nenurodyta kitaip?

Atsakymas

"SuperUser" autorius "Journeyman Geek" siūlo tokį supratimą:

Well, kind of. Fan speed control is done by varying voltage or through Pulse Width Modulation (using a constant voltage and cutting it up into pulses to vary speed). If you’re plugged into a motherboard, that’s what it does. If it has 3 wires, the third wire tells the motherboard what’s the speed the fan is running as. If you have a 4th wire, fan speed control is done via PWM rather than voltage control.

You can plug in a 2 wire fan to a 3 or 4 wire connector (though you lose speed feed back), and a 3 wire to a 4 wire connector (where you lose PWM control). You can also use a fan controller to control speeds.

Else, assuming the power source is unaware it’s a fan (as it would be connected through molex for example), and is at a fixed voltage, yes, it goes at full speed all the time.

Fellow contributor "Hyperslug" atkreipia dėmesį į tai, kaip išimtis išryškėja:

Like the other guys said, pretty much yes, but I can think of 3 exceptions:

1. A few fans have a built in thermistor that will adjust speed depending on temperature.

2. PSU’s with specially marked Fan-Only PSU connectors (Antec TruePower 550W) can adjust the speed of the fan:

3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.
3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.

Ir ten jūs turite tai: išorės valdymas naudojant tam tikrą mechanizmą (ar tai būtų pagrindinės plokštės įvestis, termometras ar intelektualus blokatorius) ventiliatoriai dirbs kuo greičiu, kurį leis maitinimo šaltinis.

Ar turite ką nors įtraukti į paaiškinimą? Garsas išjungtas komentaruose. Norite skaityti daugiau atsakymų iš kitų "Tech-savvy Stack Exchange" vartotojų? Patikrinkite visą diskusijų temą čia.

Rekomenduojamas: